 |
 |
|
|
|
 |
|
|
|
|
 |
Parixit
Industries Limited
706, Silver Oaks,
Near Mahalakshmi Cross Roads,
Paldi , Ahmedabad.
Ph No : 079 - 66318121(10
Lines) Fax No : 079 - 66318125
E-Mail :
ho@parixit.com |
|
|
|
|
|
Drip Irrigation System |
|
 |
Indian agriculture is dependent on
limited natural water sources, which
is unable to irrigate the entire
cultivated land with traditional
flood irrigation systems, as more
than 50% of the total water is lost
due to seepage, evaporation and
percolation beyond the root zone of
the plants. With traditional flood
irrigation our poor farmers are able
to irrigate only a part of their
valuable cultivated land, limiting
their income to a great extent. As
water levels in the entire country
go down, it is time for the farmers
to adopt modern irrigation
techniques in order to maximize
irrigated area, agricultural produce
and income by proper agricultural
irrigation. |
|
|
|
|
Parixit Industries Limited provides
the best and controlled irrigation
to the cultivated land of the
farmers through the most economical
way of water management.
Parixit Drip Irrigation System
provides the exact amount of water
to the root zone of the plant at a
pre-determined rate which is
calculated after the successful
research done by qualified
agronomists in different conditions
considering the types of soil,
nature of plant, age, spacing
between plants and rows,
temperature, humidity and
availability of water.
Parixit Drip Irrigation System
includes ISI marked Mainline,
Submainlenes, integral drip lines
Lateral, Drippers and is supported
by a wide range of fittings to suit
all type of conditions resulting in
to better life of Parixit Drip
Irrigation System. The whole system
is operated through ISI marked
‘Parixit’ Screen/Disc filters.
Parixit Drip System also provides
best quality of gravel/sand/hydro
cyclone filter supported by
‘Parixit’ heavy duty quarter turn
polypropylene ball valves.
Characteristics of Parixit Drip Systems :
- Main Line, Submain Line, Laterals, Driplines, Drippers & Filters are ISI marked.
- ALL components are made from the highest grade virgin raw material.
- System is supported to suit any given condition.
- Parixit Drip System operates at very Low pressure.
- We provide excellent after sales services backed by qualified agronomists and sales engineers.
Benefits of Parixit Drip Systems :
- Parixit Drip System saves water up to 70%
- Parixit Drip System irrigates larger area than any other irrigation system
- Keeps moisture in the roots and thus keeps the soil soft
- This system saves tremendous 40-50% labour and electricity costs
- Any soluble fertilizers or pesticides can be given to plants directly by Parixit Drip System
- Parixit Drip System is designed by qualified agronomists and sales engineers
Water is pumped in Mainline through
Parixit Sand and Screen Filters. To
apply Fertilizer Tank or Ventury is
connected to Mainline and is
controlled by Heavy Duty 'Parixit'
Ball Valves. Total area is divided
in predetermined sections where
Submain lines are laid for water to
reach every corner. ‘Parixit' ISI
marked laterals are connected to
Submain lines with robust Fittings
while "Parixit ISI marked Drippers
are connected to laterals near roots
of Plants. The System is controlled
by 'Parixit ' Valves to minimize the
labour cost for highest yields. |
| |
|
|
PARIXIT INTEGRAL DRIP LINE
Parixit Industries Limited
introduces inline emitting pipe
system as a part of their commitment
towards continual development. This
product conforms to Indian standards
as per IS: 13488. This is an
integral (built in) emitting pipe
system in which the emitters are
inserted in the laterals during the
extrusion process at pre-set
distances. |
|
|
MAJOR FEATURES :
- High clog resistant emitter designed with a unique wide turbulent flow path.
- Large surface inlet screen orifice.
- Two orifice outlets placed 180º apart at each dripper end.
- The additional outlet reduces the suction hazard from sand particles when the laterals are drained.
- Easy to roll and unroll during inter-cultivating operations, thus reducing chances of mechanical damage without losing drippers.
- Uniform emission rate along the lateral.
- Available in wide range of emitter spacing from 20 to 150 cm as per customer's need.
SPECIFICATION
Manufactured in Class - 1,2,3,4
Pressure ratings, with different
emission
rates:
Diameter
(mm) |
Class |
Pressure Rating
Avg. Wall (kg/cm2) (mm) |
Avg. Wall
Thickness(mm) |
| 12 |
3
4 |
2.5
4.0 |
1.1
1.2 |
| 16 |
1
2
3 |
1.0
1.25
2.5 |
0.8
0.9
1.3 |
Recommendation: Maximum Recommended
Dripline length (m) on flat Terrain
at a pressure of 1 kg/cm2 Diameter
12 mm, 16 mm.
Diameter
(mm) |
20 |
30 |
40 |
50 |
60 |
75 |
90 |
100 |
150 |
Maximum
Extendable
Lateral
Length
|
|
1.2LPH |
64 |
99.2 |
115.2 |
142.4 |
163.2 |
185.6 |
203.2 |
233.6 |
300.8 |
|
16mm |
2 LPH |
40 |
62 |
72 |
89 |
102 |
116 |
127 |
146 |
188 |
| |
4 LPH |
25 |
35 |
44 |
52 |
59 |
70 |
78 |
85 |
111 |
|
12mm |
2 LPH |
22 |
31 |
38 |
46 |
53 |
63 |
71 |
77 |
103 |
OPERATING RANGE : Working Pressure
Range: 0.7 kg/cm2 to 2.25 kg/cm2
APPLICATION : All field crops like
Sugarcane, Cotton, Strawberry,
Grapes, Carnations, Floriculture,
Banana, Pineapple, Vegetables, Tea
gardens, Green Houses, etc. |
| |
| |
|
|
| |
Identification Key:
|
| |
|
DATA SHEET for 12mm & 16 mm
Lateral Pipes: |
|
|
| |
| |
Test Results |
Acceptance
Norms |
Reference |
|
A |
Raw Material Test |
|
|
1
2 |
Designation (MRS)
Melt Flow Rate
(I 2.16) |
2.5 Mpa at 35ºC
2.0 to 3.0 Gm/10 min.at
190º C |
IS 12786:1989
IS 2530 : 1963
|
|
B |
Dimensions &
Tolerances: |
|
|
| |
Nominal Outside Diameter |
12 mm + 0.3 mm
16 mm + 0.3 mm |
IS 12786:1989 |
| |
Wall Thickness |
12 mm
16 mm |
Class
I
1.0 – 1.2mm
1.2 – 1.4mm
|
Class 2
1.1 – 1.3mm
1.4 – 1.6mm
|
IS 12786:1989 |
| |
Length |
Coil of
25,50,100,150,200 mtrs
or as agreed between
manufacturer and
Purchaser. |
IS 12786:1989 |
| |
Visual Appearance
(Surface Finish)
|
Satisfactory |
IS 12786:1989 |
|
C |
Performance Requirement |
|
|
| |
Reversion Test |
Max 3% |
IS 12786:1989 |
| |
Hydrostatic Pressure
Resistance |
Type Test:
Duration: 100 hrs. at
70ºC
Stress Values : 2.5 Mpa
Acceptance Test:
Duration : 01 hrs at
20º C
Stress Values: 6.9 Mpa |
IS 12786:1989 |
| |
Tensile Test &
Elongation |
10 Mpa
350% |
IS 2530 : 1963 |
| |
ESCR |
No crack visible on
specimen surface |
IS 12786:1989 |
| |
Carbon Black Content
& Dispersion
|
2.5 ± 0.5%
Satisfactory
|
IS 2530 : 1963 |
|
D |
Identification
Marketing & Color |
Colour: Black
All pipes shall be indelibly marked by ink/paint or hot foil embossing. One
Blue strip applied on lateral in the longitudinal direction.
a) Manufacturer's Name
b) Designation of Pipe
c) Batch Number
Key for Batch No:
Digit 1&2: Year of Manufacture
Digit 3&4: Month of mfg.
Digit: 5&6 Serial number
|
IS 12786:1989 |
|
| |
|
|
|
|
| |
Identification Key:
|
| |
|
DATA SHEET for INLNE 12mm & 16 mm
Emitting Pipes: |
|
| |
| |
Test Results |
Acceptance
Norms |
Reference |
|
A |
Raw Material
Test |
|
|
1
2 |
Designation (MRS)
Melt Flow Rate
(I 2.16) |
2.5 Mpa at 35ºC
0.8
to1.0 Gm/10 min .at 190º
C |
IS 12786:1989
IS 2530 : 1963
|
|
B |
Dimensions &
Tolerances: |
|
|
| |
Nominal Outside Diameter |
12 mm + 0.3 mm
16 mm + 0.3 mm |
IS: 13488:1992 |
| |
Wall Thickness |
12 mm
16 mm |
Class I
(0.1Mpa)
0.5– 0.7 mm
0.7– 0.9 mm |
Class 2
(0.125 Mpa)0.6– 0.8mm
0.8– 1.0mm
|
IS: 13488:1992 |
Class 3
(0.25 Mpa)
1.0 –1.2 mm
1.2 –1.4 mm
|
Class 4
(0.4 Mpa)
1.1–1.3 mm
1.4–1.6 mm
|
| |
Length |
As agreed between
manufacturer and
Purchaser. |
IS: 13488:1992 |
| |
General |
The Emitting pipes, its
parts fittings shall
have no manufacturing
defects that may impair
their performance.
|
IS: 13488:1992 |
|
C |
Performance Requirement |
|
|
| a. |
Uniformity of Emission
Rate |
The mean emission rate
of the test sample shall
not deviate from the
nominal emission rate(qn)
by more than 10% for
category B |
IS 12786:1989 |
| b. |
Emission Rate of
Emitting unit as
Function of inlet
Pressure |
Plot the curve q as
function of inlet
pressure. The curve
deviation shall not
greater than ± 10% |
IS: 13488:1992 |
| c. |
Flow Path |
The smallest measured
flow path dimension
shall not be smaller
than the dimension
declared by the
manufacturer. |
IS: 13488:1992 |
| d. |
Spacing |
The spacing of the
emitting unit shall not
deviate by more than ±
5% from the spacings
declared by
manufacturer. |
IS: 13488:1992 |
| e. |
(a) Resistant of
Emitting pipe to
Hydrostatic Pressure
i. At ambient temp.
ii. At elevated temp.
|
The emitting pipe
assembly shall withstand
the test pressure
without showing signs of
damage to the emitting
pipe. The unit emitting
pipe shall not pull
apart and no leakage
shall occur at the inlet
fittings. Leakages not
exceeding the emission
rate on one emitting
unit are permissible at
centre fittings. The
nominal flow rate in the
test specimen shall not
vary by more than ± 10% |
IS: 13488:1992 |
| f. |
(b) Resistance of
Emitting pipe to tension
at elevated temp. 50 ±
2º C |
Emitting pipe shall
withstand the test pull
out without breaking or
rearing the distance
between the two marked
lines shall not vary by
more than 5% .The
nominal flow rate in the
test specimen shall not
vary by more than ± 5% |
IS: 13488:1992 |
| g. |
Resistance to pull out
of joint between
fittings & emitting pipe |
The fitting shall not
pull out from the
emitting pipe. |
IS: 13488:1992 |
| h. |
ESCR |
No crack visible on
specimen surface |
IS 12786:1989 |
| i. |
Carbon Black Content
& Dispersion
|
2.5 ± 0.5%
Satisfactory
|
IS 2530 : 1963 |
|
D |
Identification &
Marketing |
Color: Black All
pipes shall be
indelibly marked by
ink/paint or hot
foil embossing.
a) Manufacturer's
Name
b) Designation of
Pipe
c) Batch Number
Key for Batch No:
Digit 1&2: Year of
Manufacture
Digit 3&4: Month of
mfg.
Digit: 5&6 Serial
number
|
IS: 13488:1992 |
|
| |
|
|
Top |
| |
|
| |
|
)
)
)